In this article
Disclaimer: this content is published for information. Home canning of low-acid foods carries a real risk of botulism if procedures aren’t followed to the letter. Always use tested recipes (for example from the USDA or jar manufacturers) and your appliance’s manual.
Pressure canning is one of the most effective ways to build lasting food reserves. It lets you preserve meats, vegetables, legumes and many other low-acid foods safely for months or years. This guide covers the fundamentals, how to choose a pressure canner and the good practices to adopt from the start.
Understanding pressure canning
Canning means placing food in a clean, airtight jar, then heating the whole thing. The heat destroys the microorganisms and enzymes responsible for spoilage. It also drives air out of the jar: as it cools, the lid is pulled inward, creating a vacuum seal that prevents any recontamination.
The process dates back to 1809 and is credited to the Frenchman Nicolas Appert, who was looking for a way to supply armies on campaign. Today, this method remains one of the most reliable ways to build food supplies that are stable at room temperature.
Fundamental principle: for low-acid foods — vegetables, meats, legumes — only pressure canning reaches the temperatures needed to destroy botulism spores. A boiling water bath isn’t enough.
What you need to can well
- Fresh food, properly washed and prepared
- Clean jars in good condition
- New self-sealing lids
- The method suited to the type of food (pressure or water bath)
- Processing times and temperatures appropriate to your altitude
Comparing canning methods
Water bath
Filled jars are immersed in water brought to a boil. Simple, with no specialized equipment. The maximum temperature reached is 100 °C (212 °F). Suitable only for acidic foods: jams, pickles, tomatoes with added acid.
Pressure
Pressurized steam reaches 115 to 121 °C (240 to 250 °F). Essential for low-acid foods: vegetables, meats, poultry, legumes. It is the only method that reliably destroys botulism spores.
Methods to avoid
Oven canning
An oven can’t heat the contents of jars uniformly to the required temperature. Botulism spores can survive. Jars can also shatter. This method is not recommended.
Inversion canning
This involves pouring very hot food into a sterilized jar, then turning it upside down to create a vacuum. The resulting seal isn’t reliable enough, and the cooking temperatures don’t necessarily destroy dangerous microorganisms. A water bath is less demanding and safer for acidic preparations.
Method comparison table
| Method | Temperature reached | Suitable foods | Verdict |
|---|---|---|---|
| Water bath | 100 °C (212 °F) | Acidic foods: jams, pickles, fruit, acidified tomatoes | Safe for acidic foods only |
| Pressure canner | 115 to 121 °C (240 to 250 °F) | Vegetables, meats, poultry, fish, legumes, broths | The only safe method for low-acid foods |
| Oven | Uneven inside the jar | None | Never use |
| Inversion | Insufficient | None | Never use |
| Electric multicooker | Variable, often insufficient | None, unless the model is approved for canning | Avoid for low-acid foods |
Choosing a pressure canner
Three main criteria guide the choice of a canner: capacity, the type of pressure regulation, and compatibility with the heat source available.
Capacity
For serious canning, a canner of at least 20 litres (about 21 US quarts) is recommended. A pot this size holds about seven 1-litre (quart) jars per cycle. Some models let you stack jars in two layers, which doubles the output per batch and is a real time saver.
Type of pressure regulation
Weighted gauge
A weight on the vent automatically lifts if the pressure exceeds the set threshold. Available at 5, 10 or 15 psi depending on the model. No reading to interpret: the canner jiggles or rocks to signal that pressure has been reached. Generally considered easier to use day to day. Less suited to very high altitudes, where pressure must be adjusted precisely.
Dial gauge
A gauge shows the pressure in real time. Allows fine adjustments, useful at altitude. On the other hand, you have to manage the heat source to keep the pressure stable, and the gauge should be checked for accuracy about once a year.
Heat source compatibility
Many aluminum canners don’t work on induction cooktops. Some can also scratch glass cooktops. Before buying, check compatibility with your stove, especially if you plan to use an alternative heat source for resilience.
Very large canners are extremely heavy once filled. It is best to plan how you use them so you don’t have to move them when loaded.
Overview of common models
The models below are common references on the North American market. Availability and ranges vary over time and between retailers; always check that the model you choose is explicitly designed for pressure canning (not just pressure cooking) and comes with a manual that gives canning procedures.
All American — top all-round choice
This canner is often cited as the North American benchmark for serious canning. Its most notable feature is that it has no rubber gasket: the lid seals metal to metal, which eliminates the risk of a cracked gasket or having to replace it. Regulation is by a weighted gauge adjustable to 5, 10 or 15 psi. It comes in several sizes, some of which let you stack jars to process up to 19 one-litre jars or more in a single batch.
Strengths
- Several sizes available (10.5 to 41.5 US quarts, about 10 to 39 litres)
- No gasket to replace
- Weighted gauge regulation (5, 10, 15 psi)
- Sturdy, durable construction
- Jar stacking possible (large sizes)
Watch points
- Very heavy when loaded
- High price
- Not compatible with induction cooktops
- Small handles
Presto 23-quart — affordable option
The Presto stands out mainly for its affordable price and for the availability of an induction-compatible model, which is rare in this category. It has a dial gauge and an automatic rubber overpressure plug that releases if the pressure exceeds 15 psi. The rubber gasket means eventual replacement over time.
Strengths
- Affordable price
- Light
- Induction-compatible model available
Watch points
- Regulator supplied as standard set at 15 psi; processing pressure is monitored on the dial
- Dial gauge (less intuitive)
- Rubber gasket to replace periodically
Mirro 22-quart — best value
The Mirro offers an interesting combination: a weighted gauge adjustable to 5, 10 or 15 psi, jar stacking, several built-in safety features (a latch that prevents sealing if the lid is misaligned, a lock that blocks opening under pressure, a backup overpressure release window), all at a much lower price than the All American. The rubber gasket remains its main long-term weak point. Without a dial gauge, it is less suited to high altitudes where precise adjustments are needed.
Strengths
- Weighted gauge (5, 10, 15 psi)
- Several safety features
- Jar stacking possible
- Accessible price
- Reasonable empty weight
Watch points
- Rubber gasket to replace
- Not induction compatible
- Not ideal at high altitude (no dial)
Granite Ware 20-quart — budget alternative
A budget option in anodized aluminum with a distinctive look. It has a weighted gauge (5, 10, 15 psi) and two overpressure valves — one gives a warning whistle, the other takes over if the first fails. It can also be used as a steamer. On the other hand, anodized aluminum can scratch glass cooktops, jars can’t be stacked, and the silicone gasket will eventually need replacing.
Additional equipment
Jars
Jars designed specifically for canning — commonly called Mason jars in Quebec and Canada — are recommended. They are made to withstand thermal shock and have a calibrated rim that reliably takes self-sealing lids.
The question of reusing commercial jars (pasta sauce, mayonnaise, etc.) comes up often. These containers usually have narrower sealing surfaces and thinner walls, which increases the risk of seal failure or breakage during processing. If you make this choice for economic reasons, accept the risk and always check that the two-piece lid fits the jar rim properly.
Lids
Canning lids have two pieces: a flat disc with a sealing compound around its edge, and a screw band. The band can be reused from batch to batch. The disc should not be reused: the sealing compound is compressed during the first cycle and no longer guarantees a reliable seal.
When fitting, the screw band doesn’t need to be tightened very hard. The seal must be tight while still letting air escape during processing.
Note: after taking the jars out of the canner, don’t retighten the screw band. Doing so can break the seal as it forms.
Racks
Racks serve three functions in canning:
- Raising the jars to avoid direct contact with the bottom of the pot, which could make them break.
- Keeping the jars stable and letting steam circulate around them.
- Making it easier to remove the jars without burns.
Most canners come with their rack. If it is lost, a temporary solution is to tie screw bands together and lay them on the bottom of the pot. This improvisation raises the jars but doesn’t replace the holding and handling functions of the original rack.
Basic pressure canning instructions
The steps vary slightly depending on the canner model. Always consult the manual supplied with the appliance. The general steps are:
- Pour 5 to 8 cm (2 to 3 in) of hot water into the canner (or as directed by the manufacturer).
- Place the filled jars on the rack inside the canner.
- Close the canner lid according to the model’s instructions.
- Make sure the vent is open.
- Put the canner on the heat source at high heat. Let steam escape through the vent for about 10 minutes before closing it.
- Close the vent. Pressure will build inside.
- Start timing the processing once the required pressure is reached.
- If the pressure drops during processing, bring it back up and restart the timing from the beginning.
- When the processing time is up, turn off the heat and let the canner depressurize naturally. Never force cooling with cold water.
- Once the pressure is back to zero, open the vent and wait about 10 minutes before removing the lid.
- Remove the jars and let them cool at room temperature for 12 to 24 hours without handling them.
Important: never open the canner before the pressure has fully dropped. Forcing it open can cause a violent spray of steam or scalding liquid.
Practical tips
Sterilizing jars and lids
Pressure canning doesn’t require sterilizing the jars beforehand. The high-temperature processing cycle does that job. It is still useful to preheat the jars before filling them — not to sterilize them, but to avoid thermal shock that could crack them. Just fill them with hot tap water a few minutes before use.
Lids shouldn’t be boiled. Boiling can soften the sealing compound and reduce its ability to form an airtight seal. A rinse in hot water is enough.
Hot pack or raw pack
Hot pack
Food is briefly precooked (2 to 5 minutes in water or syrup), then poured hot into the jars. This method removes trapped air around the food better, shrinks it beforehand and lets you fit more into each jar. It is generally the preferred method.
Raw pack
Raw food is packed firmly into the jar, then a boiling liquid (water, juice, brine) is added. Simpler to prepare, but the food tends to float and leave trapped air, which can cause discolouration over time.
Headspace
Headspace is the empty space left between the contents and the rim of the jar. It is needed because air and food expand when heated. General guidelines:
- 6 mm (¼ in) for jams and jellies
- 12 mm (½ in) for fruit and tomatoes in a water bath
- 25 to 32 mm (1 to 1¼ in) for vegetables and low-acid foods in a pressure canner
Salt and sweeteners
Salt and sweeteners in canning recipes mainly serve to adjust taste, texture and colour. They have no preserving role in pressure canning. They can be left out or adjusted to taste, with no effect on safety or shelf life.
Altitude and pressure
Water boils at a lower temperature as altitude increases. For canning, this means adjusting either the pressure or the processing time according to your altitude. Serious canning recipes and guides usually include these adjustments. It is important to consult and apply them, especially if you live in a mountainous area.
Pressure guidelines by altitude
| Altitude | Weighted gauge | Dial gauge |
|---|---|---|
| 0 to 305 m (0 to 1,000 ft) | 10 psi | 11 psi |
| 306 to 610 m (1,001 to 2,000 ft) | 15 psi | 11 psi |
| 611 to 1,220 m (2,001 to 4,000 ft) | 15 psi | 12 psi |
| 1,221 to 1,830 m (4,001 to 6,000 ft) | 15 psi | 13 psi |
These guidelines match the USDA’s general recommendations for most vegetables and meats. They don’t replace the time and pressure given in a tested recipe. In Quebec, the vast majority of homes are below 305 m (1,000 ft), but some communities in the Laurentians, the Appalachians or Charlevoix are higher.
Testing seals after cooling
Once the jars have cooled (12 to 24 hours), remove the screw bands and check each seal. Two simple methods:
- Press the centre of the lid: it shouldn’t flex or make a popping sound.
- Look at the lid at eye level: it should be slightly concave (curved toward the inside of the jar).
A jar whose seal isn’t airtight should be refrigerated and eaten soon, or reprocessed within 24 hours with a new lid.
Always label
Once the jars have cooled and the seals have been checked, label each jar with its contents and the canning date. This simple habit helps you manage stock rotation and avoid eating canned goods that are too old.
Food safety and botulism
Most microorganisms on food are eliminated by heat and by the oxygen-free environment created in an airtight jar. One important exception: Clostridium botulinum, the bacterium responsible for botulism.
This bacterium occurs naturally in soil and on raw food. In healthy adults and children, its spores swallowed with fresh food generally pose no danger — except in infants under 12 months, in whom they can germinate in the gut (which is why babies aren’t given honey). However, in an oxygen-free, low-acid environment — such as a canning jar — it can produce toxins that are extremely dangerous to health.
Simple boiling (100 °C / 212 °F) is enough to destroy the bacterium itself, but not its spores. To eliminate the spores, you need to reach at least 115 to 121 °C (240 to 250 °F), which only pressure canning achieves reliably and practically.
Safety reminder: pressure canning is the only recommended method for safely preserving vegetables, meats and all low-acid foods at room temperature.
Good practices to prevent botulism
- Wash all fresh produce thoroughly before canning
- Peel root vegetables
- Use pressure canning exclusively for low-acid foods
- Follow the recommended processing times and pressures
- Adjust processing parameters for altitude
- Never eat the contents of a jar whose seal is doubtful or that smells abnormal when opened
If in doubt about a jar’s integrity, don’t taste the contents to judge its safety. Botulism toxins can’t be detected by smell or taste in some cases. Throwing the jar out is the only prudent decision.
Frequently asked questions
Can you can in an electric multicooker?
Generally, no. Most electric multicookers don’t hold a pressure and temperature that are stable and verifiable enough for canning low-acid foods. Only appliances explicitly designed and tested for pressure canning should be used for this purpose.
How long do home-canned goods keep?
For best quality, home-canned goods are generally best eaten within about 12 to 18 months. As long as the seal stays intact and the contents show no sign of spoilage, they usually remain safe longer, but texture, colour and nutritional value decline.
What signs mean a jar should be thrown out?
A bulging lid or one that no longer holds, oozing liquid, rising bubbles, cloudy liquid, mould, an abnormal smell, or liquid spurting when opened. In all these cases, don’t taste: throw the jar out without opening it further, placing it in a closed bag, and clean any surfaces it touched.
Can you use a pressure canner on a propane stove?
Yes, provided the stove is stable, powerful enough, and used outdoors or in a well-ventilated space, according to the manufacturer’s instructions. The flame must be able to hold a constant pressure for the entire processing time.
Further reading
See long-term food storage, food-grade plastics and water storage and pemmican: a safe recipe and storage.

